Casting machine ( Chopping runners, Cutting runners, Breaking gates)

32-1 Casting Splitter
ep1ep2  

EP-30~EP-150

 

This machine is for splitting gate in casting industry.

It can work by HIRADO hydraulic pump (200~400V 3-phase).

The way to cut the gate using grinder, gas and hammer is too hard and dangerous.
Our product can solve the matter and change the work environment better. This machine adapt the wedge principles. Therefore, it is easy to split the gate.

 

Regarding the size of the gate, please check [Casting Splitter Model Selection Chart] below.

  • The Gap of the gate : 12mm to 90mm
  • Average shape of the gate : 15×15 to 50×50(mm)

 

Please click the following link to know more detail.

EP-30(20)EP-40EP-80N(23)EP-80N(23)L

EP-80N(30)EP-100(32)EP-150(32)

 

– Inside of parenthesis is opening width (mm)

– N means new model

– L means long wedge ( to split the gate at the )

e-ep1

 

 

 

 

 

32-2 Snap Cutter
sch1

sch2

SCH-1S、SCH-1

 

This machine is for cutting Runner, Sprue of Cast iron, Aluminum and Cast copper.

It can work by HIRADO hydraulic pump (200~400V 3-phase).

Using grinder, gas and hammer is common way to cut the gate, runner and sprue is too hard and dangerous job. This machine is powerful, easy to operate and smaller footprint.

It is suitable for cutting 35 to 50mm of gate, runner, sprue, etc.

 

※Click here to read more.

32-3 Snap Breaker
shb1

sbh2

 

1. SBH-1~3

 

This machine is for breaking runner such as FC, FCD.

It can work by HIRADO hydraulic pump (200~400V 3-phase) and hanged by Spring Balancer.

The way to break the gate using grinder, gas and hammer is too hard and dangerous. Our product can solve the matter and change the work environment better. This machine adapt the lever principle. As breaking runner into small pieces , the melting furnaces can work efficiently to save huge of electricity.

 

Regarding the size of the runner, please check [Snap Breaker Model Selection Chart] below.

 

Average shape of the gate

  • FC : up to 85mm
  • FCD : up to 70mm

Please click the following link to know more detail.

SBH-1SBH-1LSBH-2SBH-2LSBH-3

 

sbt1

sbt2

 

2. SBT-2、SBT-2A

 

This machine is for breaking runner such as FC, FCD.

It is stationary type and work by HIRADO hydraulic pump (200~400V 3-phase).

It is more suitable for thick runner than HIRADO SBH series.

 

Average shape of the gate

  • FC : up to 85mm
  • FCD : up to 70mm

 

Please click the following link to know more detail.

SBT-2SBT-2A

 

sbt1001

sbt1002

 

3. SBT-100

 

This machine is for breaking runner such as FC, FCD.

It is stationary type and work by HIRADO special hydraulic pump.

It is the most powerful among HIRADO SBT series, suitable for thick runner.

 

Average shape of the gate

  • FC : up to 120mm
  • FCD : up to 100mm

 

 

※Click here to read more.

 

e-sbh

 

 

 

32-4 Gate Breaker
epg1

epg2

EPG-3、EPG-10

 

This machine is for splitting gate in casting industry.

It can work by HIRADO hydraulic pump (200~400V 3-phase).

The feature of this machine is wide blade opening size, and suitable for splitting small gate.

 

  • The Gap of the gate : 12mm to 88mm
  • Average shape of the gate : 15×15(mm)

 

Please click the following link to know more detail.

EPG-3EPG-10

 

 

 

 

32-5 Runner Crusher
hrc1

hrc2

 

HRC-2

 

This machine is for breaking runner such as FC, FCD.

It is stationary type and work by HIRADO special hydraulic pump.

It is large type machine among HIRADO products, can break runner into small pieces. Therefore, it can be time saving. Moreover , melting furnace will be used effectively because of small pieces if runner and to save the cost of electricity.

 

 

 

※Click here to read more.

 

 

 

 

 

31-6 Aluminum Cutter
auc1

auc2

AUC-20

 

This machine is for cutting gate of Aluminum and Cast copper.

It can work by HIRADO hydraulic pump (200~400V 3-phase).

It can work more efficiently and quickly compared to grinder, gas and hammer.

 

  • Average shape of the gate : 20(mm)

 

※Click here to read more.